The limited operational lifetime of organic solar cells remains an obstacle to their commercial development and is largely due to the poor intrinsic photostability of the conjugated molecules that constitute the photoactive layer. Here, we selected a series of state-of-the-art donor and acceptor materials including PBDB-T, Y5, PF5-Y5, and PYT to study their photostability under AM1.5 simulated sunlight in ambient conditions. Their properties are monitored over time, using various spectroscopy techniques, including UV-Vis absorption, Fourier-transform infrared (FTIR), and X-ray and ultraviolet photoelectron spectroscopy (XPS and UPS). We found that the absorption spectra of Y5 and PYT films remain almost intact even after 30 hours of light exposure in air, while the PF5-Y5 and PBDB-T films undergo rapid photobleaching. The absorption losses observed in blend films of PBDB-T with Y5 and with PF5-Y5 can be understood as composed of contributions from the separate blend components that are similar to the absorption losses in neat films. The new peaks emerging in the FTIR spectra of PBDB-T, PF5-Y5, and their blend films witness the formation of new carbonyl groups, while these are absent in the spectra of the Y5 and PYT films. The XPS C 1s spectra of the PF5-Y5 and PBDB-T films confirm this carbonyl formation and the S 2p spectra reveal that sulphone groups are formed after 30 hours of exposure of these films. These results confirm that films of Y5 and the copolymer PYT are significantly more resistant to photooxidation, compared to the copolymer PF5-Y5. The comparison of these results suggests that the benzo[1,2-b:4,5-b ']dithiophene moiety with alkylated thiophenes as side chains (BDT-T) accelerates the photodegradation of PBDB-T and PF5-Y5. The replacement of the BDT-T unit by thiophene contributes to the enhanced stability of PYT, demonstrating that the nature of the co-monomer has a significant effect on the intrinsic photostability of Y5-based copolymers. These new insights are expected to stimulate the design of stable donors and acceptor polymers for the development of long-lived OPV devices. Absorption spectra show the photobleaching of acceptor copolymer PF5-Y5. The replacement of BDT-T by thiophene strongly improves the photostability.

Mixed-halide perovskites enable bandgap engineering for tandem solar cell and light-emitting diode applications. However, photoinduced halide phase segregation introduces a compositional instability, that is, formation of I-rich and Br-rich phases, which compromises photovoltaic efficiency and stability. While optical and structural studies of the photoinduced phase segregation in mixed-halide perovskites have been reported, its impact on the material stability is missing. Here, a detailed compositional analysis of mixed-halide perovskite films using x-ray and ultraviolet photoelectron spectroscopy (UPS) was carried out to determine how their stability in various environments depends on the halide ratio. A series of perovskite thin films were fabricated with the composition CH3NH3Pb(IxBr1−x)3, where x = 0.00, 0.25, 0.50, 0.75, and 1.00, and analyzed under different conditions, such as exposure to light in ambient and in nitrogen atmosphere, as well as storage in the dark. From the spectroscopy results, complemented with structural and optical properties, it was found that the deletion of halide ions from the surface is facilitated in mixed-halide perovskites in comparison with pure halide perovskites. A higher stability was found for the mixed-halide perovskite containing less than 25% Br, and it decreases with increasing Br content. This study also established the effect of the Br/I ratio on the energy landscape of the materials. The UPS spectra reveal that photoinduced degradation results in a mismatch of the energy levels at the perovskite/transport layer interface, which may limit the collection of charge carriers. These findings correlate well with the photovoltaic device stability under similar degradation conditions.

Sputtered nickel oxide (NiOx) has become one of the most promising inorganic hole transport layers for p–i–n perovskite solar cells (PSCs) due to its appealing features such as its robust nature, low material cost, and easy integration to tandem structures and large-area applications. However, the main drawback with NiOx-based PSCs is typically low open-circuit voltage (VOC) due to the inferior energy-level alignment, low charge mobility, and high recombination at the interface. Herein, two types of phosphonic acid self-assembled monolayers (SAMs) deposited by blade coating as an interfacial layer to modulate the sputtered NiOx/perovskite interface properties are used. While sputtered NiOx serves as a conformally coated hole selective layer, the ultrathin SAM interlayer facilitates the hole extraction and minimizes the energy loss at the interface. Co-ordinately introduced stabilizing additive, namely octadecyl 3-(3,5-di-tert-butyl-4-hydroxyphenyl)propionate (I-76), further improves the device performance of NiOx/SAM-based PSCs, resulting in VOC of 1.14 V and a power conversion efficiency of 21.8%. By applying these strategies for perovskite module upscaling, aperture area module efficiencies of 19.7%, 17.5%, and 15.5% for perovskite minimodules of 4, 16, and 100 cm2 are demonstrated, corresponding to active area module efficiencies of 20.4%, 18.0%, and 16.4%, respectively.