Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • apa.csl
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Chassiintegrerade lastceller: Installation i fjädersäte på Scania tandemboggibakaxlar
Karlstads universitet, Fakulteten för teknik- och naturvetenskap, Avdelningen för maskin- och materialteknik.
2014 (Svenska)Självständigt arbete på avancerad nivå (masterexamen), 20 poäng / 30 hpStudentuppsats (Examensarbete)Alternativ titel
Chassis integrated load cells : Installation in spring seat on Scania tandem boogies (Engelska)
Abstract [en]

The thesis presented in this report has been made on behalf of Scania and their basic frame design department with the subject to solve an implementation of a weight sensing system in the chassis. The system is supposed to be implemented in the seat springs, and the reason for this is that all the force will have to go through the weight sensing transducers. With all the force going through the transducers the weight sensing system will not be sensitive for the differences in tolerances from manufacturing. The transducers could be pre-calibrated to avoid a calibration of the whole vehicle after it’s completed from the manufacturing line.

Weight sensing systems is today a reality in trucks with air springs. Complete systems is also sold in the big aftermarket for trucks. None of Scanias competitors have a solution for this as of today.

The thesis was from start limited to only process the BT-301S bogie. A system will likely be easy to adapt to the other bogies with small modifications.

Through the thesis possible problems are illuminated to understand the function and make a properly working weight sensing system. In the present bogie system the main problem for a proper function is the frictional forces that appears in the surface between the spring and the spring seat. 

In the report a proposition with a rubber part between the spring and the spring seat is introduced, with the idea to get around the known problems with the frictional forces. The rubber itself does produce a reaction force when deformed, but the forces could through simulation be known, and hence compensated for. A rubber part under the spring would result in a contact surface much higher than today. A new spring, or a new version of the spring, will be needed for this solution to work.

For the work to come, Scania need to decide what precision the weight sensing system need. But smaller decisions like the size and stiffness for the rubber part will also be needed. This thesis has only dealt with the bogie, but in a close future, the front axles need to be done. Much can likely be carried over from this thesis for that.

A weight sensing might be possible to implement, but with what precision at uneven ground? Most likely will the variation in load on the transducers be too much. An approximation for the precision with a total span of 7% is realistic.

Ort, förlag, år, upplaga, sidor
2014. , s. 63
Nyckelord [sv]
maskinteknik, lastceller, trådtöjningsgivare, lastbil, fordon
Nationell ämneskategori
Annan maskinteknik
Identifikatorer
URN: urn:nbn:se:kau:diva-33663OAI: oai:DiVA.org:kau-33663DiVA, id: diva2:746677
Externt samarbete
Scania CV AB
Ämne / kurs
Maskinteknik & Materialteknik
Utbildningsprogram
Påbyggnadsprogram i Maskinteknik mot civilingenjörsexamen, inriktning Materialteknik 120 hp
Handledare
Examinatorer
Tillgänglig från: 2014-09-16 Skapad: 2014-09-14 Senast uppdaterad: 2014-09-16Bibliografiskt granskad

Open Access i DiVA

Chassiintegrerade lastceller(9189 kB)534 nedladdningar
Filinformation
Filnamn FULLTEXT01.pdfFilstorlek 9189 kBChecksumma SHA-512
b7b6de3dddbe47d9169773a4720a483eec234d489995fe8b70b15791804b31f1d333c37e04c4e7b6a1f1cbfbea187832b154182d429e791c37502cc988cf903a
Typ fulltextMimetyp application/pdf
Arkivfil(9189 kB)188 nedladdningar
Filinformation
Filnamn FULLTEXT02.pdfFilstorlek 9189 kBChecksumma SHA-512
b7b6de3dddbe47d9169773a4720a483eec234d489995fe8b70b15791804b31f1d333c37e04c4e7b6a1f1cbfbea187832b154182d429e791c37502cc988cf903a
Typ fulltextMimetyp application/pdf

Av organisationen
Avdelningen för maskin- och materialteknik
Annan maskinteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar
Totalt: 722 nedladdningar
Antalet nedladdningar är summan av nedladdningar för alla fulltexter. Det kan inkludera t.ex tidigare versioner som nu inte längre är tillgängliga.

urn-nbn

Altmetricpoäng

urn-nbn
Totalt: 4407 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • apa.csl
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf